Chosen Solution All lights work including brights and blinkers but not the low beams First things first, check your fuses. By brights I suspect you mean hi beam. Low beam has its own fuses for left and right. So check those out, if they are good, check the relay, you can usually swap it out for another of the same type. Last of all check your bulbs, chances are they’ve just blown....
Chosen Solution I have filled both bags of rocks and the bags won’t move. I tried to empty out the bags and refill them, but that still didn’t fix my problem. Stripped gears are the likely cause for the GravityLight to become jammed. Since the gears are damaged and cannot mesh properly, the gears will become stuck. The gears will need to be replaced by removing the front panel and the frame....
Chosen Solution when i open any application , even settings or contacts getting white screen and freeze. i tried restore OS but same, and tried replaced touch screen assembly still same. Does it freeze all the time you have your phone on and it shows a white screen or does it happen sometimes. If it happens sometimes and the phone is somewhat functional try these’s steps down below. 1 - The first thing is to make sure that your iOS device is connected to the Internet....
Chosen Solution I have replaced my resivor cap, water pump, thermostat, and bled it added new 50/50 had it flushed and cleaned twice and my car is still overheating not long after it warms up. It makes a bubbling sound and runs hot and the temp rises . I was told from a friend that is a mechanic it sounds to him like the intake gasket needs replaced. I am lost when it comes to cars....
Chosen Solution why is my blu studio 5.0S II not updateing Your phone is corrupted. You will have to factory reset the immediately let it update, back up your data first Update (10/13/2016) My Blue studio xl was exactly same way. Sometimes the updates can cause phone to “bootloop” if you interrupt any part of the update. I got impatient after installation because BLU logo screen stayed on for a few minutes but it was part of the process....
Chosen Solution I topped off fluids on my 01 focus zx3 …then I see tons of smoke in the rear window every time I step on the gas. What did I do wrong?? Did you check the oil when the car is not running. It sounds like you put to much oil in the engine. I would go to a repair shop or parts store and have them verify the oil level....
Chosen Solution My device gets very hot and sometimes turns off unexpectedly. Help. It’s possible for a device to overheat from dust in the vent or fan. Make sure the vents and fans are clear of dust and debris.
Chosen Solution [img]https://image.ibb.co/jT2r5x/X4Sigma.jpg[/img] [img]https://image.ibb.co/csr15x/28450309_101…[/img] i boght a new fridge freezer, after a day it stopped cooling, i looked on the back and saw a frozen pipe near the compressor, could this be down to low refrigerant or the fan? Hi @goukifafa , If it is new, take it back and get it replaced under warranty
Chosen Solution My screen is shaking up and down occasionally before it locks itself…. I previously changed the screen after it cracked I have this problem too and it only seems to be with Sony Expedia. The shop staff were no help so I have to get in touch with Sony again and send it back
Chosen Solution It’ll tap randomly anywhere ani can’t play anything how do I fix it its annoying You may need to replace the digitizer. Try to restore to factory settings (backup your data before that) and see if this help. Good luck
Chosen Solution the machine fills with water while being on or off. Hi, What is the model number of the washer? Try turning off the water supply faucets (hot and cold) to the machine, one at a time and check if it stops filling when either one is turned off. It may be a water inlet solenoid valve in the machine that is faulty but knowing whether it is the hot or cold will help....
Chosen Solution samsung tab.overheating If your question is: why is my tablet to slow when I’m on it. Well, probably it’s going to be your ram memory that’s full ;)
Chosen Solution i have problem. my go pro won’t turn on when i insert the battery. but the device become overheat. what may caused this problem?what should i do?thank you. @subki_hussin overheating when the battery is inserted is pretty indicative of a short circuit. Could be a shorted battery as well as a bad power circuitry etc. Exchange the battery for a new one and see if that resolves anything. After that you will have to start disassembling your GoPro and check for any visible damage etc....
Chosen Solution I need help, my iPhone turns off itself after auto-lock somebody help me please Most likely a problem to do with your firmware or OS. Try making a backup and then restoring to that backup. If that still doesn’t work then restore it without any backup. But make sure you back up your contacts with Gmail or some other service that apple offers in iTunes. I got the same problem I found out that the problem was occured by connector 3 of the screen....
Chosen Solution i repaired my phone with a new motherboard and im having boot issues. its keeps saying : SECURE FAIL: RECOVERY system software not authorized by AT&T has been found on your phone. please turn off your phone and go to the nearest AT&T store for help. How do i fix this issue? Hi you will need to use odin to reflash the stock firmware for your device. I would suggest using xda as a point of reference....
Chosen Solution I have hooked the iPad Air up to my computer and it says I need to erase it and restore it. I have tried this and keep getting error codes. I called apple and they said I need to send it in and the repair will cost approximately $300. Is there a way I can fix it myself? My guess is that this is corrupted NAND and is not repairable....
Chosen Solution Where is written the IMEI on the RAZR? Shouldn’t it be written somewhere on the device? This article should walk you through how to find out your phone’s IMEI number. Hope this helps. Good luck!
Chosen Solution I bought the iFixit pro kit but I don’t know which screw should I use it says 1.2 or 2.8 or what ever but I can’t find it like it says under the screw in the ifixit kit like T5 or P2 or 2 or 0.5 if I could know that. it would be awesome . You use P2 (Pentalobe 2) for taking the two bottom screws near the charging socket to allow you to lift up the screen....
Chosen Solution I replaced my screen on my iPad. Now it has a white screen only. Still haven’t glued my screen down till I fix it but need help. What’s wrong with my iPad. Why is it a white screen only but makes sounds and everything? Was the digitizer glass changed or was the LCD display changed? Note that the LCD Display from a Mini 1 is not compatible with the Mini 2 and vice versa....
Chosen Solution Just wondering, because I always have to look up the EMC Version on Mactracker instead of staying on your page. Other sections use the names of the devices, like “iMac Mid 2010”… Thanks (ifixit is great, btw. without you I wouldnt repair anything I guess) Here’s the skinny on Apples use of EMC numbers, everything you ever wanted to know and more, even where to locate them. https://beetstech.com/blog/understanding…...
