Posts

Chosen Solution Hello all, does anyone know which microphone the iPhone 6 uses while the phone is on speaker? My phone works fine but when I switch to speaker phone the other end can not hear me at all. I already replaced the microphone thats attached to the front camera and it still doesn’t work. Any input is greatly appreciated. I think its the microphone located near the ear piece speaker, it would be a cheap and easy fix....

Chosen Solution My tablet has lnes in the middle ts red at times an today it’s white have seen v3 lines at times new tablet only a few weeks have seen up to 3 different color of lnes don’t have anyideal what to try Jerry Hardee could be an issue with the LCD TAB connection. Post an image of what those lines look like Adding images to an existing question If it is the TAB’s then it is not a DIY repair but needs a replacment LCD...

Chosen Solution When I call people, they can’t hear me but I can differently hear them. When I record my voice or a video, you can everything going on, but not on call. Phone: J7 Prime … closet to my phone in picture. Check first activate on phone when caling handsfree/loundspeaker output or connect headphone with microphone…. also you can try clean microphone hole, maybe is inside some dirty

Chosen Solution When I plug in my headset its says its not connected and I tried resetting and updating my controller and console over and over again and still wont work. Even when it is plugged in it acts like its not plugged in and I plugged in the headset hard and still wont work. What do I need to do? Hi @agent40d , It seems that there may be a faulty headphone socket in the controller....

Chosen Solution When I am calling someone I usually have it on speaker mode for example when my parents called and I pass it on to my siblings. However, recently people and my parents have said that they can not hear me well. I did a test with my sibling’s other phones with and without speaker mode on and there is a difference. When I have it on no speaker mode they hear well but when I do it loose connection....

Chosen Solution My LG 50LN5400 screen goes black after a few millisecond when I turn my Tv on. I ‘ve done the flash light test, I can see the image behind and the sounds works fine. Plz help Thomas Serra in that case it is a backlight issue. It could be the power board, the main board and the backlight array. Your sereis TV has issues with the backlight array itself....

Chosen Solution I have reseted it already and I don’t why this is happening. I was wondering if someone can tell me how to fix it or the price to fix it. I have never dropped it in water or dropped it in general. Perhaps maybe something stuck in the earphone jack? When it freezes, does it just shut off and reboot? Theirs nothing stuck in the head 0hone jack I just need to know how to fix

Chosen Solution Hello - This is model DUL200PKS1. Every thing is working fine with out any diagnostic lights, except for the unit filling and draining multiple times at the start of the cycle. Heating element works fine. It does complete the cycle, it just wastes heated water at the start of the cycle. I’ve checked the float switch and works fine. I don’t really want to swap parts without a good diagnosis, and would prefer to not buy new if it is repairable!...

Chosen Solution my flip 5 whenever connected to my or anyone phone seems to play the music perfectly for about 3 minutes then starts skipping every 3-5 seconds. I have already tried JBL support and factory resetting it. Any Ideas? NONE of those is the reason, and every troubleshooting option they have is BS and does nothing. This affects the JBL Xtreme 3 of the same generation tech too. It seems JBL has just massively screwed up the new line....

Chosen Solution Is it possible to do a factory data reset under this policy? Mine did this, and my antivirus had root/reset blocked. Simply punched my 6 digit antivirus code into my antivirus app, and then set the setting to not block root/reset. Fixed—just like that. i did that and it sent me to safe mode Yes, it is possible, but only by doing a hard reset. Instructions from the LG site for this are as follows....

Chosen Solution When the power adapter is running, the motor makes a loud noise similar to a card in bicycle spokes only much more intense. There is nothing visibly interfering with the brushes. It is especially noticeable when pulled backwards. Take the brush out and find what is stuck in it acting as a card. Shark Navigator Roller Brush Replacement

Chosen Solution My print looks like this: HP LaserJet 5M page Note the background is gray and the text is barely readable. I have a new toner cartridge (does the same thing with my old toner cart too) Reference this: Wikipedia - Laser Printing The problem you are encountering is the failure of the charged toner particles from jumping from the drum to your paper. This is where a positively charged “transfer roller’ or wire is used to alter the drums charge has failed....

Chosen Solution When I press the R2 (right trigger) the left analog stick moves (not physically) to the left. It is interfering directly as I saw it using the DS4windows software to analyze the input data. What might be the problem? Hardware? Software? Some years passed i see - but maybe someone will use it :) I had this problem too and it was solved by cleaning potentiometer on X (up and down) axis of Left Stick....

Chosen Solution Recently I just changed my battery and charging port. After installing both new parts I noticed when I used both the charging port or wireless charging it has not charged. The battery I received was dead. Is this a sign of a bad battery or charging port? Im sure it is the battery since the wireless charging and regular port is not charging the phone. Make sure the battery is plugged in secure....

Chosen Solution When I turn on my ps2, the disc game can’t be read because it doesn’t spin. does it spin initially at all? or do you put the disc in and it does nothing? if it does nothing the motor is probably finally dead. youll either need to source a new motor and replace your self or replace the whole assembly. or send it to Sony for repairs

Chosen Solution Installed a Sonnet Creescendo G3/L2 upgrade card in my TAM. It powers up with light green, the disks starts but doesn’t boot, and screen remains black. Tried to reset PRam, CUDA button, unsuccessfully. You may need the power macintosh card control panel installed for it to boot properly. In my experience I needed it in order to boot without the card enabled first and then install sonnet software and switch the card back on in the power macintosh card panel....

Chosen Solution My blue life 8 won’t charge. The charging port looks fine. When I plug it in the charger . it will grab charge for 1 second. And then won’t charge at all. The charging port tends to come unattached from the phone and needs to be fixed also my new phone the tips that you plug in some are smaller size so when you plug it in it won’t charge but some have a tight fit which it means its a bet bigger and it fixed the problem you need to find the right charger even though there all the same type the may look the same but some are a tiny bit bigger which makes the perfect fit because the charging port tends to move around while charging it....

Chosen Solution My charging port is damaged. I need to repair but do no know where the suitable shop. First click on this link to see if one of the 11 different models has a dude for it and tell us which one it is: Alcatel Phone Repair

Chosen Solution Hi all, Trying to assess whether my washing machine’s fault is one that is worth of repair or if I should just get a new one. It had started making some loud clunking noises during the wash programme, and then when a load was in, it suddenly lit up the ‘Service’ light and displayed fault code F06. Now, when i try to turn the drum manually it feels like it’s obstructed on an anti-clockwise turn....

Chosen Solution I accidently changed something in settings and now I have to doubletap to open anything and in settings I can’t scroll down to the bottom. You probably activated talkback mode, watch this video to turn it off.