Chosen Solution i factory reset the chromebook because it was an old school chromebook and the screen went dim but the brightness was all the way up, I can’t afford to fix it if I have to pay for it, is there any really cheap or free way to fix it? @emi00 depends on how dim is dim. It is possible that this is a backlight error or a panel LED driver error....
Chosen Solution The screen started flickering and its maximum brightness has slowly diminished to the point where I can barely tell that it is on. I tried finicking with the display cable to ensure it was not being pinched anywhere, but that did not help. Are there any possible solutions other than the LCD dying? Well the other potential causes is the screen connector coming loose from behind the display. Other than that it would be the display cable and worse case screen needing to be replaced....
Chosen Solution Hi, I have just replaced my 3DS XL hinge and case. Therefore, I have taken out the motherboard and reassemble back. After that I am not able to turn it on again. There is no LED light up. But when I plugged it to the charger, there is the orange LED lighted up and the moment I pressed the power button, the blue LED lighted up for 3-4 seconds and disappear....
Chosen Solution I did charge it at night before sleeping and by 6 AM I woke up and get my tablet and then it did not turn on. What happened? I had this problem once, a few weeks ago. Pressing on and volume + or - didn’t work. No heat detected while charging. I opened the asus, disconnected then reconnected the battery(found the procedure on youtube): the asus started and showed battery symbol near zero....
Chosen Solution the camera is not broke . but it is not working Did you replace it with a new non-OEM one? The flashlight has to be grounded properly to the frame. If not, it will not flash properly. Try using the teardown guide in reverse to make sure the camera parts are intact.
Chosen Solution when I turn on my imac I hear the chime and the crt but it displays nothing Take the back off and examine the capacitors for swelling and/or leakage. Next step would be to go over the video board with a soldering iron looking for “cold solders”. You can get a very good electrical jolt from the CRT so look up how to discharge it. Nevermind, here is a video on how to do it: https://www....
Chosen Solution I purchased a new Samsung Momentus 4TB hard drive for my iMac (EMC 2638). The old 1TB drive functioned OK, I just needed more space. I hooked the new drive up with an external USB cable and formatted it. Next I took the new drive out of the iMac and then used a duplicator and made a sector by sector duplicate of the old drive to the new one....
Chosen Solution My LG G2 screen occasionally become like this. Touch screen still works. Probably something inside is loose due to drop while a few knocks on it can bring it back to normal. However, yesterday dropped another time and knocking does not help this time.. for awhile screen was dark but after putting a tape under the white antenna cable the noisy screen is back. Would like to know better what/which connector is affecting it....
Chosen Solution I have an hp ProDesk running windows 7. The fans have been running fast and sound like a jet engine…..i have pulled the side panel off and blew the inside out with compressed air and then restarted….same issue…. Try adjusting the power plan of your computer, (Start menu> search “Power plan” > “choose a power plan”> set to power saver. Then restart computer. Try running PC with side open (if it goes away it may be a heat issue with your case)....
Chosen Solution I’ve recently purchased an Ender 3 3d printer(not 3 pro) and have already assembled it. I have also leveled it. Though for some reason, all my prints are extrememly innacurate and messy. Why? What it was supposed to look like: What printed: Of course I stopped the print before It could mess up even more. I’ve attempted this again and the results were similar. Other prints also have spacings between the infill and edge...
Chosen Solution Hi, I am a user of a Dell Latitude E7440. The last time the laptop powered on was when it was on the power cable, while I was playing Cruise Ship Tycoon on Roblox. Then, suddenly, the screen went black, the power, hard drive and charging lights all went off, the fans stopped, and it didn’t boot up ever again. I tried a lot of methods, and they don’t work....
Chosen Solution Hello, I’m posting on behalf of my friend’s laptop. These are the problems that he’s noticed: Starts heating up a lot so the fan speeds up to compensate and is therefore loud. At this point the trackpad usually becomes slow and jittery. The laptop turns off soon after. The laptop activity when this happens is very mild e.g. watching YouTube videos or browsing the web.The laptop only turns on when holding SHIFT down along with the power button....
Chosen Solution I’ve had this laptop for about 3 years, but this problem surfaced about 4 months ago. The laptop will suddenly switch off, and will make a high pitched “click” noise as soon as the screen turns black. The “click” sound as best as I can describe, sort of sounds like a fingernail flicking the power button, but more high-pitched and mechanical. I timed the intervals between each turn-off and it is about 25-30 minutes....
Chosen Solution I’ve got a late 2012 unibody mac mini. Recently, the fan started making a rapid clicking noise when running. Initially, cleaning the fan and vents with compressed air seemed to help, but then the noise returned. After some experiments, I discovered that pressure on the bottom plate causes the noise; apparently the bottom plate is rubbing against the fan, creating the noise, and slowing or sometimes stopping the fan....
Chosen Solution I can see through the viewfinder, however the image is distorted and neither zoom nor outo-focus seem to be able to fix it. If the photo that was taken by this camera is distorted of some sort, there are a few reason why this occurred. One, the lens may be a little skewed or even cracked. This guide will show how to replace and remove the broken or skewed lens in order to align or replace these lens....
Chosen Solution Do I must replace the Touch ID if I replace the logic board on a1932 MacBook Air 2018 The TouchID unit is bonded to the logic board electrically. The logic board won’t accept the wrong TouchID unit. Apple designed it this way to protect your systems content from people or government spying. Look at it this way… the TouchID unit and the fingerprints it stores is like your cars fob & keys you need both to gain entrance into your car and drive it....
Chosen Solution I have the same charger that came with the computer and when I checked the motherboard and battery it still does not work Hi @mrfixer2011 , Have you checked that there is 19.2V DC at the charger’s output plug, you didn’t say? If the charger’s output voltage is OK but there is no voltage on the motherboard it may be a faulty DC-In jack (supplier example only to show what the part looks like and the cost)....
Chosen Solution When in use, my compressor is excessively noisy and sometimes rattles as well. Check to make sure the pump is level. Remove shroud and check for loose components in the compressor. Tighten all loose components accordingly. If the rattling still continues, it is most likely a problem with a bearing or cylinder in the pump assembly. You will need to replace the Pump Assembly. Happy Fixing
Chosen Solution When I got my echo spot I really liked it but then for some reason it started flickering and I tried everything. Dimming the display, getting a new power supply and factory resetting it. So I really hope someone can come up with an answer for it. I was ready to toss the spot–though it’s one of my favorite Alexa devices. Driving me nuts, the screen flicker. Hard reset, moving to a new location, just couldn’t fix it....
Chosen Solution The power trips immediately when the fridge is plugged in Check to verify that the outlet is NOT a GFCI outlet. The fridge should be plugged into a standard outlet. If the above is not hte problem, then the compressor may have a problem that is causing a short which would trip the breaker. You can also check for a short by measuring the resistance across the two paddles of the plug....
